Differenze tra le versioni di "3.PROVA PRATICA CCNA 6.0 PACKET TRACER"
| Riga 55: | Riga 55: | ||
Router#conf t | Router#conf t | ||
Router#(config)int gigabitEthernet 0/0 | Router#(config)int gigabitEthernet 0/0 | ||
| − | Router#(config-if) description First Floor LAN | + | Router#(config-if)description First Floor LAN |
''' La stessa cosa si fa con la Gigabit 0/1 ''' | ''' La stessa cosa si fa con la Gigabit 0/1 ''' | ||
Versione attuale delle 21:00, 16 mag 2019
GUIDA ALL'ESAME PRATICO CISCO CCNA 6.0 (PACKET TRACER)
Indice
- 1 Performance Component: IP Addressing Design
- 2 Performance Component: IPv6 Host Address Configuration
- 3 Performance Component: Router Interface Configuration and Addressing
- 4 Performance Component: Host Default Gateway Configuration
- 5 Performance Component: Switch Management Interface and Telnet
- 6 Performance Component: Initial Device Configuration
Performance Component: IP Addressing Design
Questa parte viene svolta con l’uso dell’interfaccia
IPv4 LAN 1 Subnet Calculation:
PC1: Subnet Mask = 255.255.255.224
PC2: Subnet Mask = 255.255.255.224
IPv4 LAN 2 Subnet Calculation:
PC3: Subnet Mask = 255.255.255.240
TFTP Server: Subnet Mask = 255.255.255.240
IPv4 LAN 1 Host Addressing Design and Implementation:
PC1: IP Address = 192.168.1.97
PC2: IP Address = 192.168.1.98
IPv4 LAN 2 Host Addressing Design and Implementation:
PC3: IP Address = 192.168.1.145
TFTP Server: IP Address = 192.168.1.146
Performance Component: IPv6 Host Address Configuration
Questa parte viene svolta con l’uso dell’interfaccia
IPv6 LAN 1 Host Address Configuration:
PC1: IPv6 Address = 2001:DB8:ACAD:A::FF/64
PC2: IPv6 Address = 2001:DB8:ACAD:A::15/64
IPv6 LAN 2 Host Address Configuration:
PC3: IPv6 Address = 2001:DB8:ACAD:B::FF/64
TFTP Server: IPv6 Address = IPv6 2001:DB8:ACAD:B::15/64
Performance Component: Router Interface Configuration and Addressing
Questa parte viene svolta con l’uso del Terminale collegando il Router ad un qualsiasi computer via cavo Console
Router Interface Activation
1. Settare la description sulla GigabitEthernet 0/0 e GigabitEthernet 0/1
Router#conf t Router#(config)int gigabitEthernet 0/0 Router#(config-if)description First Floor LAN
La stessa cosa si fa con la Gigabit 0/1
2. Router Interface GigabitEthernet 0/0 and 0/1 IPv4 Addressing
· Router Interface GigabitEthernet 0/0 IPv4 Addressing
Router#conf t Rouer#(config)int gigabitEthernet 0/0 Router(config-if)ip address 192.168.1.126 255.255.255.224 Router(config-if)no shut
· Router Interface GigabitEthernet 0/1 IPv4 Addressing
Router#conf t Rouer#(config)int gigabitEthernet 0/1 Router(config-if)ip address 192.168.1.158 255.255.255.240 Router(config-if)no shut
· Router Interface GigabitEthernet 0/0 IPv6 Addressing and Link-local
Router#conf t Rouer#(config)ipv6 unicast-routing Rouer#(config)int gigabitEthernet 0/0 Router(config-if)ipv6 address 2001:DB8:ACAD:A::1/64 Router(config-if)no shut
· Link-local
Router(config-if)ipv6 address FE80::1 link-local Router(config-if)no shut
· Router Interface GigabitEthernet 0/1 IPv6 Addressing and Link-local
Router#conf t Rouer#(config)ipv6 unicast-routing Rouer#(config)int gigabitEthernet 0/1 Router(config-if)ipv6 address 2001:DB8:ACAD:B::1/64 Router(config-if)no shut
· Il link-local è sempre il FE80::1 e va settato allo stesso modo sulla GigabitEthernet 0/1
Performance Component: Host Default Gateway Configuration
Questa parte viene svolta con l’uso dell’interfaccia
LAN 1 Host Default Gateway Configuration:
PC1: Default Gateway = 192.168.1.126
PC1: Default Gateway IPV6 = FE80::1
PC2: Default Gateway = 192.168.1.158
PC2: Default Gateway IPV6 = FE80::1
LAN 2 Host Default Gateway Configuration:
PC3: Default Gateway = 192.168.1.158
PC3: Default Gateway IPV6 = FE80::1
TFTP Server: Default Gateway = 192.168.1.158
TFTP Server: Default Gateway IPV6 = FE80::1
Performance Component: Switch Management Interface and Telnet
Questa parte viene svolta con l’uso del Terminale collegando lo switch ad un qualsiasi computer via cavo Console
Switch Management Interface Configuration
· Assegnare il penultimo ip della seconda sottorete della quarta sottorete alla VLAN1 del secondo Switch.
Switch>enable Switch#conf t Switch#(config)int vlan1 Switch#(config-if)ip address 192.168.1.157 255.255.255.240 Switch#(config-if)no shut
· Assegnare il default gateway allo switch
Switch(config)ip default-gateway 192.168.1.158
· Dare la password a tutte le linee VTY (0 15)
Switch(config)line vty 0 15 Switch(config-if)password cisco12345 Switch(config-if)login
· Dare la password alla linea Console 0
Switch(config)line console 0 Switch(config-if)password cisco12345 Switch(config)login
· Crittografare le password settate
Switch(config)service password-encryption
· Configura Switch del secondo piano per la gestione remota su Telnet.
Switch(config)line vty 0 15 Switch(config-if)login local Switch(config-if)transport input telnet
Performance Component: Initial Device Configuration
Questa parte viene svolta con l’uso del Terminale collegando il Router ad un qualsiasi computer via cavo Console
Basic Router Configuration
· Configurazione Hostname
Router(config)hostname Middle
· Impostare la password per il Privileged Mode
Router(config)enable secret password cisco12345
· Impostare un Banner
Router(config)banner motd #Warning#
Secure Router Communication Lines
· Impostare la password alla linea Console 0
Router(config)line console 0 Router(config-if)password cisco12345 Router(config-if)login
· Criptare le password impostate
Router(config)service password-encryption
· Settare la lunghezza minima delle password
Router(config) security passwords min-lenght 10
· Consentire il protocollo ssh nelle linee vty
Router(config)line vty 0 15 Router(config-if)login local Router(config-if)transport input ssh
· Settare il dominio del router
Router(config)ip domain-name cisco.com
· Creare un utente
Router(config)username netadmin privilege 15 secret Cisco_CCNA5
· Creare una chiave rsa 1024
Router(config)crypto key generate rsa 1024
